Skip to content
English
  • There are no suggestions because the search field is empty.

Sourcing report

How to read the Sourcing tab in Reports, what each figure counts, how sources are named and what the export contains.

How to read the Sourcing tab in Reports, what each figure counts, how sources are named and what the export contains.

The Sourcing tab shows where your candidates come from and how far each source gets them. To open it, select Reports in the left-hand menu, then the Sourcing tab, or select the Sourcing card on the overview page. Who can open reports, and how the date range, filters, group views and exports work in general, is covered in "Reports overview" and "Who can see which reports".

What the tab counts

The tab counts candidates by source, using the date each candidate was first added to Recruit. A candidate is only counted if they have at least one application on a job you can see, so a person added to the talent pool who has never applied is not in these figures. There are four cards:

  • Total Sources is the number of different sources that have at least one candidate in the range.
  • Top Volume Source is the source with the most candidates, with the count underneath.
  • Best Hire Rate is the source with the highest share of its candidates hired, shown as a percentage of conversion. A source with only one or two candidates can top this card with a very high rate, so read it alongside the volume.
  • Total Candidates is the number of candidates across all sources.

The Top Volume Source and Best Hire Rate cards show a dash when there is no data.

The chart and tables

Candidates by Source

One bar per source, largest first. The longest bar is the source with the most candidates and the others are drawn to scale against it. Each bar is split into three colours: blue for In pipeline, green for Hired and red for Rejected. The number at the right end is the source's total candidates.

In pipeline is worked out as the total minus hired minus rejected. A candidate with one hired application and one rejected application is counted in both, so treat the blue segment as an approximation.

Source by Department

One row per source and one column per department, followed by Total and Hire Rate. The department columns are every department that has a job you can see. Each cell is the number of candidates from that source who applied to a job in that department, and a dash means none. Hire Rate is hired candidates divided by total candidates for the source, as a whole percentage.

The department cells do not have to add up to Total. A candidate who applied in two departments appears in both columns, and jobs with no department are not in any column.

Pipeline Stage Breakdown

One row per source and one column per pipeline stage, in pipeline order, with a final Hired column. Stages that share the same name and type across your jobs' pipelines share a column. Each cell holds three things:

  • The large number is how many applications from that source ever reached the stage, including ones later rejected or moved on.
  • The line beneath, for example 3 active, is how many are in that stage right now.
  • A line such as 60% from prev. is the number that reached this stage as a share of the number that reached the stage to its left. The first stage has no percentage.

This table counts applications, while the chart and cards count candidates. In the Hired column the figure is the number of candidates hired from that source. If nothing matches the filters the table reads No sourcing data available.

How sources are named

The report groups candidates by the source name you set up under Settings, then Candidate Sources. "Managing candidate sources" explains how to add and edit them.

  • Candidates with no source recorded appear as Unknown.
  • Renaming a source does not move the candidates already recorded against it. They keep the earlier wording and appear on their own row in lower case with underscores, for example careers_page, while new candidates appear under the new name. You then see two rows for what you think of as one source, and Total Sources counts both.
  • Deleting a source has the same effect: its earlier candidates show under the stored lower-case form.
  • Switching a source off does not change how it is reported. The name stays as it was.

If you want to stop using a source, switch it off rather than renaming it.

Date range and filters

The tab uses the Date range control at the top right. With no range chosen it shows the last 12 months, measured against the date the candidate was added. The Department and Job filters are on the Reports overview page, not on the tab. Choose them there and they carry over when you open the tab. Unlike the Offers tab, Sourcing applies both filters.

If you have group access, a company filter appears beside Export and the tab shows combined figures for the companies you choose. The Department and Job filters do not apply to group figures.

Exporting the Sourcing report

Set the date range you want, select Export, then Export as CSV or Export as Excel. The file downloads with the report and the day in its name, for example sourcing-report-2026-09-30.csv, and a message reads Report exported successfully. If it fails you see Failed to export report. Please try again. Each user can export ten times a minute. If you have not chosen a date range, the screen shows the last 12 months but the export covers all dates, so choose a range first if you want the file to match the screen.

The file holds a table of Source, Total, Hired, Rejected, In Pipeline and Hire Rate (%), then Total Sources and Total Candidates, then the Pipeline Stage Breakdown (Source, Stage, Reached, Current) and a Stage Conversions table (Source, From Stage, To Stage, Conversion Rate (%), Lost). Lost is the number who reached the earlier stage but not the next one. In the Excel file these are separate sheets. The Source by Department table and the chart are not exported.

For a full list of candidate sources with a row for each candidate, System Admins and HR users can use the Candidate Source Report template in "Custom reports".