Skip to content
English
  • There are no suggestions because the search field is empty.

Setting up two-factor authentication

How to turn on two-factor authentication, choose between an authenticator app and email, and save your recovery codes.

How to turn on two-factor authentication, choose between an authenticator app and email, and save your recovery codes.

Two-factor authentication adds a second step to signing in. After your password, Recruit asks for a 6-digit code, so a stolen password on its own is not enough to get into your account. This article is for anyone setting it up for the first time, whether Recruit requires it or you choose it.

Who has to use it

Users with the System Admin, HR or Group Admin role must use two-factor authentication. This applies in every organisation and cannot be switched off.

An administrator can also require it for everyone. The setting is on the Security page, described in the article "Security settings". When it is on, every role must enrol, including Members and hiring managers.

If neither applies to you, two-factor authentication is optional and you can turn it on yourself at any time.

Turning on two-factor authentication

If your role or your organisation requires it and you have not set it up, Recruit sends you to a page called Set up two-factor authentication. It says "Your organisation requires two-factor authentication. Please set it up to continue." You cannot open anything else in Recruit until you finish. For a first sign-in after an invitation, see Accepting your invitation and setting your password. If your password has also expired, Recruit asks you to change it first and then takes you through the setup.

  1. Select Enable two-factor authentication.
  2. Choose a method if you are asked, then follow the steps for that method below.
  3. Save your recovery codes, tick I have saved my recovery codes and select Continue to app.

To turn it on yourself, open the menu under your avatar and select Settings, then My Profile. The Two-factor authentication card reads "Two-factor authentication is not enabled." Select Enable two-factor authentication and follow the same steps. When you set up from My Profile the final button is Done instead of Continue to app.

Choosing a method

Under Choose how to verify there are two options.

  • Authenticator app: an app on your phone such as Google Authenticator or Authy. It works without a phone signal.
  • Email: Recruit emails a code to your work address each time you sign in. No phone is needed.

Your administrator decides which methods the organisation allows. If only one is allowed, you are not asked to choose and go straight to that method's steps. You can add the other method later if it is allowed.

Setting up an authenticator app

  1. Scan the QR code on screen with your authenticator app. If you cannot scan it, open Can't scan? Enter this code manually: and type the code shown into your app.
  2. Type the 6-digit code your app now shows into the code boxes.
  3. Select Verify and enable. The button stays greyed out until all six digits are entered.

If the code is wrong, you see "Invalid code. Please try again." and the boxes clear. Type the code the app is showing now.

Setting up email

  1. Recruit sends a 6-digit code to your own email address and opens a Verify your email address step. The dialog says "We have emailed a 6-digit code to [email]. It expires in 5 minutes. Enter it below to finish setting up."
  2. Enter the code from the email.
  3. Select Verify and enable.

If the email does not arrive, select Send a new code. If Recruit cannot send it you see "We could not email your code. Please try again." Wait a moment and try again. An old code shows "That code has expired. Select Send a new code to get a fresh one." Too many wrong guesses show "Too many attempts. Please wait a few minutes and try again."

Saving your recovery codes

As soon as a method is verified, Recruit shows a set of recovery codes under the heading Save your recovery codes. Each code looks like XXXXX-XXXXX and works once. They are your way in if you lose your phone or cannot reach your inbox.

  1. Select Copy all to put every code on your clipboard, or Download codes to save them as a text file named new-recruit-recovery-codes.txt. You can do both.
  2. Tick I have saved my recovery codes. The button below stays disabled until you do.
  3. Select Continue to app or Done.

Keep the codes somewhere outside Recruit, such as a password manager. Recruit has no screen for viewing your codes again later. You can only replace them with a new set.

If Recruit refuses to start setup, the message on screen says why. For example, an account with no email address shows "Your account has no email address. Please contact an administrator to enable two-factor authentication." Ask an administrator to add an email address to your user record.

If the screen says "We couldn't display your recovery codes yet", finish the setup, then go to My Profile and select Regenerate recovery codes to get a fresh set before you need one.

Related articles